A state of the Art,
New Generation Antenna from
LUSO
for the 21st Century !
The World's Leading Heavy Duty Motorized,
Big Crank-up Tower for Your Radio Communications

News

Towers

T-Rotor

Rotor

Options

Others


LUSO
===Home===

News

LUSO22EU

LUSO28EU

LUSO36EU
LUSO36XX
LUSO36MG


LUSO44XX
LUSO44MG

LUSO51XX
LUSO51MG

LUSO CRANK-UP TOWER BIG SERIES SPECIFICATION
Self Supporting Crank-up Tower
youtube LUSO51XX and XTR-51
      XTR-51 in Japan

Tower Model LUSO51XX   LUSO51MG
Maximum Height 168ft. / 51 m
Minimum Height 43.6 ft. / 13.3 m
Maximum Loaded Weight

660lbs / 300kg standard 

1320lbs / 600kg standard
Option max to 1320lbs / 600kg Option max to 2200lbs / 1ton
Wind load Capacity  108 sq.ft. / 10u 183sq.ft / 17u
Full extension wind speed : 57mph (92km/h) (25m/sec)
Bottom position wind speed : 157mph (253km/h) (70m/sec)
Structure Triangular truss
Hot dip galvanizing
Width of bottom Section 82inch / 2051mm

Length of a Section /Number of Sections

36ft. / 11m , 6 Sections
Mast Bearing Stand Mast bearing stand on the top of tower
Rotator Installation Stand 9ft. / 2610mm  below the top of the tower
Intermediate Mast Bearing Stand 6ft. / 1760 mm below the top of the tower
Control Method Full automatic (with Indoor remote controller, without cable)
Inverter control

With soft start/soft stop function

raise up and raise down Speed

Approximately 50 seconds
Winch Winch designed for LUSO170MG exclusively Doubled rollers,Winch designed for LUSO170MG exclusively
Worm reduction gear and chain drive
Drum with grooves for wires
Hot dip galvanizing then High temperature ( 392°F / 200℃ ) powder coating.
Electric Power for Winch Three phase AC 220 V
Motor Ratings Output 15HP / 11 kw 20HP / 15 kw
Motor Control Inverter control
Counter Balancer Using two units of balance weights
Elevator system
Hot dip galvanizing then High temperature ( 392°F / 200℃ ) powder coating.
Guide Roller Guide Roller designed for LUSO Big series exclusively
Nitriding hardening
Two or more bearings are used per guide roller.
Doubled Guide Rollers designed for LUSO Big series exclusively
Nitriding hardening
Two or more bearings are used per guide roller.
Pulley Pulley designed for LUSO Big series exclusively
Nitriding hardening
Two or more bearings are used per pulley.
Wire Many flexible steel wires for each side of the tower unit The safety ratio of a wire far exceeds the elevator standard for man.
Method for Detecting Top and Bottom Position

Rotary limit switch designed for LUSO Big series exclusively

Total Weight 50600lbs / 23ton 81400lbs / 37ton
Weight of Base Unit 2090lbs / 950kg
Length of Basic Unit 9′10″3000mm
Safety Fence It is an important security mechanism for preventing people contacting a machine operation section.
Three-sided fence
Shock Absorber It is an important security mechanism.
Three pieces for tower unit, Two pieces for balancer
Foundation See below
* The specification is subject to change without prior notice.

Standard Accessories
Tower Base Unit
Safety Fence
Shock Absorber
Indoor Controller and Remote Controller (for working outside)
Other costs
Cost for foundation work
Cost of instruction for installation
Electric cables for controller , power line and wind gauge
Crane charge for unloading tower from container and installation
Cost for customs clearance
Cost for electrical construction work
Domestic tax
Transportation cost : sea freight and local transportation charge
Cost for installation work

See separate page in terms of options.




elevation














Copyright2019 LUSO All Right Reserved




Others LUSO Wind Power Generator
          Golf Towers
         www.lusotower.com
         youtube